China OEM 4040 Taper Lock Bushings near me manufacturer

4040 Taper Lock Bushings

Typically, bushings are replaceable, while integral bearings are permanent and should not be replaced unless worn or damaged. Bushings are most commonly used in machinery, where they allow relative movement between components. The bushing is usually an integral unit, while the bearing may have several parts. Simple bushings can be made of brass, bronze, or steel. It is often integrated into precision machined parts and helps reduce friction and wear. Typically, bushings are made of brass or bronze, but other materials can also be used. Different designs have different applications, so you should understand what your application requires before purchasing a sleeve. The most common uses of plain bearings are in critical applications, including turbines and compressors. They are also commonly used in low-speed shafting, including propeller shafts and rudders. These bearings are very economical and suitable for intermittent and linear motion.

Dimensions of the 4040 Taper-Lock Bushings

  • Bushing Number: 4040
  • Bore: 1″、1/2″、10mm、11/16″、11mm、12mm、13/16″、14mm…..
  • Dimension (A): 5-3/4″
  • Dimension (B): 4″
  • Dimension (D): 5.54″
  • Number Of Set Screws: 3
  • Threads: 5/8″
  • Length: 1-3/4″
  • Dimension (G): 40°
  • Wrench Torque: 1,700 LBS
  • Weight: 21 LBS

Installation

1. Clean all oil, dirt, and paint from the shaft, bushing holes, bushing exterior, and bores of components (sprockets, pulleys, etc.).
2. Insert the bushing into the assembly. Match hole patterns, not threaded holes (each hole is threaded on 1 side only).
3. Thread the set screw or cap screw into the half-threaded hole shown below. Install the assembly on the shaft.
4. Alternately set the torque setting or cap screw* to the recommended torque setting in the table below.
5. Fill all unoccupied holes with grease.

Removal

1. Remove any retaining or cap screws.
2. Insert the set screw or cap screw into the above hole.
3. To reinstall, complete all 5 (5) installation instructions.

If you are replacing a transmission bushing, you will need to use a tapered lock bushing. The parts are simple but should be installed correctly. To ensure proper functionality, follow the instructions carefully. Otherwise, you may damage the bushing and void any manufacturer’s warranty. The size chart below can help you choose the right bushing for your needs. Use it as a guide when ordering.
The diameter of the shaft bore and its length determines the size of the Taper-Lock bushing. The taper reduces the length of the through-hole and allows the bushing to fit better than flanged bushings. The taper is 8 degrees long, so a 1.5″ diameter taper is 1-1/2″ long. For metric applications, the metric designation is “MM”. Taper locking bushings are flush with sprockets or pulleys.
The Taper-Lock bushing system allows the sprocket hub to be smaller than ever. The through-hole length dimension has been reduced by approximately 3%, and the shaft can be mounted close to the bearing without any problems. These bushings feature tapered handles with wedge action, making them easy to install and remove without deforming the shaft. These bushings come in different sizes and styles.

Click and check out more products you’re looking for.

Q1. Are you a factory?
A. Yes. We are a factory with more than 15 years of manufacturing experience.

Q2. Is OEM and ODM service available?

A. Of course. We have many years of experience in OEM& ODM service.

Q3. I am buying from another supplier, but need better service. Would you match or beat the price I am paying?
A. We always feel we provide the best service and competitive prices. We would be happy to personalize a competitive quote for you,email us.

Additional information

Edited

CX